Central Vacuum Sizing and Inlet Placement

Central vacuum & cabling · 5 min read · Updated November 2026

A central vacuum is sized and laid out house by house: the inlets are placed so a hose reaches every room, and the power unit goes in a basement, garage, crawl space or utility room. We plan it on your floor plan rather than from a one-size rule.

Key points

  • Layout starts with the floor plan and the hose you will use.
  • The power unit sits in a basement, garage, crawl space or utility room.
  • Inlets are placed for whole-house coverage and ease of cleaning.
  • Stairs, closets and the garage often get their own considerations.
  • New builds can plan tubing in the framing; existing homes use a careful route.
Central vacuum hose and wand on a hardwood floor

A formula, such as one inlet per so many square feet, sounds handy. We do not use one, because a floor plan with stairs, tall ceilings and furniture does not fit one. What we can tell you is what we look at when we plan the layout.

Why we do not use a formula

A single number for inlets per square foot sounds helpful and is usually wrong. Two houses with the same size can need very different layouts because of walls, doors and furniture. The goal is simple: inlet valves are placed for whole-house coverage and maximum cleaning convenience. We reach that by looking at your house.

Where the power unit goes

The power unit is the motor and canister. It can be located in a basement, garage, crawl space or utility room. We look for a spot that is easy to reach for emptying, has space around it and keeps the tubing run to the rest of the house reasonable.

Because the unit exhausts and needs to be reached for service, the location is a design decision and not just a place where it fits. See central vacuum systems for the overall service. BEAM, one of the brands we install, describes its power units and inlets on its own site.

Inlet placement, step by step

Inlets are the wall sockets you plug the hose into. The goal is a hose that reaches the whole floor without dragging around corners.

  1. Mark each floor on the plan and where the furniture will sit.
  2. Choose inlet spots in hallways or central rooms where the hose can reach into the rooms on either side.
  3. Add inlets where you clean often, such as stair landings, the kitchen and the garage.
  4. Check hose reach through doorways and around corners.
  5. Review the plan with you before any tubing is run.

Areas that need their own thought

Stairs, finished basements and garages are the usual extra spots. A garage inlet is handy for cars and workshops. Stairs can be cleaned from a landing inlet instead of a hose stretched to the next floor. Upstairs and downstairs levels are usually planned as separate zones for the hose.

Pets, a workshop or a home with a lot of tile or hardwood might change which spots matter most. Tell us how you actually clean.

New construction or existing home

In a new home the tubing runs through open framing, so layout choices are broad. See our new construction page, and add central vacuum to your prewire checklist.

In an existing home the route goes through attics, crawl spaces and closets. Our retrofit page says installation can usually be completed in less than one day, and in most cases without damage to the home. The layout still comes first.

What to bring to the consultation

A floor plan helps, even a hand sketch with room names. Mark where beds, sofas and large furniture sit, because inlets behind a sofa are no use. Note the places where you vacuum most: entry mats, pet areas, stairs, the garage. Photographs of the possible power unit spot, including a wide shot of the basement, crawl space or utility room, let us start the layout before we arrive.

We bring the experience of many installs, and the only thing we do not bring is a fixed number. Your house sets the layout.

Our license for this work

Central vacuum work is done under Nevada State Contractors Board license 0039080, listed in the state's license search. Seeing a layout on paper is part of our free on-site consultation.

Sources (2)

Related questions

How many inlets does my house need?

It depends on the layout, not a fixed formula. We plan inlets so the hose reaches every room and the areas you clean most.

Where can the power unit go?

In a basement, garage, crawl space or utility room.

Can I choose where inlets go?

Yes. We recommend spots from the floor plan, and you tell us what fits how you clean.

Do stairs need their own inlet?

A landing inlet can be a convenient way to clean stairs without a long hose. We discuss it during planning.

Do you plan inlets for a home that is not built yet?

Yes. New construction is the easiest time because the tubing goes through open framing.

More questions and answers

Let’s start a conversation.

Call 775-355-0831